Same Day Dispatch, Next Working Day Delivery! *Subject to stock

Sealing Concrete Tiles

Sealing Concrete Tiles on an existing floor

We've put together some easy to follow advice on sealing Concrete tiles when using Aqua Mix Tile & Stone Products. Please note all information given on sealing Concrete tiles is for guidance purposes only and all products should be used in accordance with their supplied instructions. Always test products in a small area before committing to sealing all of your Concrete tiles.

Step One: Water test Concrete tiles

1382551064_84a5195001
1 Put a few water droplets directly onto the Concrete tiles at various locations.
  1. Allow the droplets to remain for 5-10 minutes, then blot dry with absorbent towel.
  2. If the water marks stay darkened for a period of time in excess of 5 minutes, the existing sealer on the Concrete tiles is ineffective, proceed to step three.
  3. If the water marks dry quickly and the tiles return to their normal colour within 2 - 3 minutes proceed to step two.

Step Two: Remove existing sealer from Concrete tiles

removing old sealer from Concrete tiles with Aqua Mix sealer & coating remover
Using Aqua Mix Sealer and Coating Remover
  1. Sweep, mop or vacuum Concrete tiles removing surface dirt and debris
  2. Apply product with mop or sponge
  3. Allow Aqua Mix Sealer and Coating Remover to dwell up to 1 hour without drying or until coating or residue softens. Do not allow Sealer & Coating Remover to dry on surface - if Remover starts to dry, add more to ensure surface is kept wet.
  4. Agitate with a scrub brush or scrub machine.
  5. Wipe up residue with clean, absorbent white cotton towels or sponge. A wet-dry vac may be used.
  6. Removal of thick coatings or residue may require several applications - repeat from start if coating is still on surface.
  7. Rinse thoroughly with clean water.

Step Three: Clean Concrete Tiles

cleaning Concrete tiles with Aqua Mix heavy duty tile & grout cleaner
Using Aqua Mix Heavy Duty Tile & Grout Cleaner
  1. Sweep, vacuum, or wipe surface.
  2. Mix Heavy-Duty Tile & Grout Cleaner as follows:
  3. LIGHT SOIL BUILD-UP: Mix 1 part cleaner to 5 parts water. MODERATE SOIL BUILD-UP: Mix 1 part cleaner to 3 parts water. STRIPPING OR HEAVY SOIL BUILD-UP: Mix 1 part cleaner to 2 parts water.
  4. Apply solution to surface with mop or sponge.
  5. Allow to dwell 3 to 5 minutes for cleaning, or 5 to 10 minutes when stripping waxes or finishes.
  6. Agitate with synthetic mop, scrub brush, or scrub machine. Do not allow solution to dry on surface.
  7. Mop up dirty solution.
  8. Rinse thoroughly with clean water

Step Four: Seal Concrete Tiles

sealing Concrete with Aqua Mix sealers choice gold
Using Aqua Mix Sealers Choice Gold for a natural look
  1. Surface must be clean, dry, and free of existing sealers or coatings.
  2. Apply using a sponge, brush, paint pad, cotton towel, or sprayer. NOTE: Be sure any sealer that does not penetrate surface is removed from surface within 5 minutes of each application using absorbent paper or cotton towels.
  3. If 2 or more coats are applied, allow a minimum of 30 minutes drying time between coats.
  4. 2 hours after final coat conduct a test to determine if surface is completely sealed by applying water droplets to the surface. If water is absorbed, apply an additional coat. Wait 2 hours and repeat the test.
  5. Ready for surface traffic in 2 hours after final coat. Keep area dry for 12 hours. Achieves a full cure in 24 hours.
  6. Clean applicator tools with water after each use.

sealing Concrete with Aqua Mix enrich n seal
Using Aqua Mix Enrich 'n Seal for an enhanced and darken look
  1. Surface must be clean, dry, and free of existing sealers or coatings.
  2. Apply using a sponge, brush, paint pad, cotton towel, or sprayer. NOTE: Be sure any sealer that does not penetrate surface is polished dry off surface within 5 minutes of each application using absorbent paper or cotton towels. If non-polished surfaces are left shiny after application, surfaces must be wiped dry as this indicates surface residue remains.
  3. If 2 or more coats are applied, allow a minimum of 30 minutes drying time between coats. Remove surface residue after each application.
  4. Ready for surface traffic in 12 hours after final coat. Keep dry for 12 hours. Achieves full cure in 48 hours. Some highly porous surfaces may require an additional coat after full cure.
  5. Clean applicator tools with mineral spirits after each use.

Sealing Concrete tiles with Aqua Mix ultra-solv
Using Aqua Mix Ultra-Solv

  1. Apply using a sponge, brush, paint pad, cotton towel, or sprayer. NOTE: Be sure any sealer that does not penetrate surface is polished dry off surface within 5 minutes of each application using absorbent paper or cotton towels.
  2. If 2 or more coats are applied, allow a minimum of 30 minutes drying time between coats.
  3. After 2 hours conduct a test to determine if surface is completely sealed by applying water droplets to the surface. If water is absorbed, apply an additional coat. Wait 2 hours and repeat the test.
  4. Ready for surface traffic in 2 hours after final coat. Keep area dry for 12 hours. Achieves a full cure in 24 hours.
  5. Clean applicator tools with mineral spirits after each use.
About Concrete
Concrete is a construction material composed of cement (commonly Portland cement) as well as other cementitious materials such as fly ash and slag cement, aggregate (generally a coarse aggregate such as gravel limestone or granite, plus a fine aggregate such as sand), water, and chemical admixtures. The word concrete comes from the Latin word "concretus", which means "hardened" or "hard".